What Does Scratch and Dent Mean?
Scratch and dent means an appliance is new or open-box but has cosmetic damage on the outside, like a scratch, scuff or dent, while the working parts are unaffected. The machine runs exactly like the undamaged unit next to it; you are paying less because the finish is not perfect.
For most buyers the question is not whether scratch and dent appliances are worth it, but whether the mark will show once the unit is installed. This guide walks through how the damage happens, where it usually sits, and what to check before you buy.

What Scratch and Dent Means
The term covers any appliance that works but has a visible cosmetic flaw. A refrigerator with a dent in the side panel, a range with a scuff on the back, a dishwasher with a small scratch on the door. The compressor, the heating element, the controls, all the parts that actually do the job are fine. The discount exists because the outside is not showroom clean.
Scratch and dent is different from used. A used appliance has been owned and run in someone's home for years. A scratch-and-dent unit may never have been plugged in. It is closer to new in function, just marked up in appearance.
How the Damage Happens
Most cosmetic damage happens in transit or on the showroom floor. A forklift clips a carton and the corner of a fridge takes a small dent. A delivery truck hits a bump and a range shifts against its bracing, leaving a scuff. A unit sits on a display floor and picks up a scratch from a customer's bag or a restocker's belt buckle.
Sometimes the damage happens before it reaches us, at the manufacturer or a distribution centre, and the unit is marked down instead of scrapped. In every case the appliance is tested before it goes out. If the damage affects function, it does not get sold as scratch and dent. It goes to repair.
Why It Is Cheaper
A dent on the side of a refrigerator drops the price because most buyers want a flawless finish, and the retailer cannot sell a marked unit as new. The discount is the cost of that cosmetic imperfection. For you, the trade-off is simple: if the mark will be hidden once the unit is installed, you are getting a working appliance for less money with no real downside.
How much you save depends on the unit and where the damage is. A mark on a visible door panel means a bigger discount than a dent on the side that slides against a cabinet. The savings can be meaningful, often enough to move you up a model or add the matching appliance you were going to skip.
Where the Damage Usually Is
Cosmetic damage tends to land in a few predictable spots. On refrigerators it is the side panels and the back, the parts that face a wall or cabinet. On ranges it is the back panel and the sides, hidden by counters. On dishwashers it is often the side or a corner of the front frame that tucks under the counter edge.
The marks that matter least are the ones you will never see after install. A dent on the left side of a fridge that slides into a cabinet opening is invisible in use. A scuff on the back of a range is behind the unit. The marks that matter more are on the front door or the top, the surfaces you look at every day.
What Does Not Matter Once Installed
A scratch on a side panel that sits against a wall is gone the moment the unit is pushed into place. A dent on the back of a range is hidden behind the appliance. A scuff on the bottom edge of a dishwasher is covered by the toe kick. None of these affect how the appliance runs, and none of them show in your kitchen.
The only marks worth weighing carefully are the ones on the front, the door, or the control panel. Even then, a small scratch near a handle is a personal call. Some buyers do not care; others want a clean front. There is no wrong answer, only what you are comfortable living with for the money saved.
What to Check Before You Buy
- Ask where the damage is. The single most important question. A side or back mark is usually a non-issue; a front mark is a judgement call.
- Picture it installed. Think about which faces will be visible in your space. A dent on the side matters less in a built-in alcove than in a freestanding spot.
- Confirm the function is unaffected. We test every unit, but ask to hear it run or see the controls cycle. Cosmetic damage should never touch the working parts.
- Check the warranty terms. Scratch-and-dent models carry a 1-year repair or exchange warranty, the same as our open-box units.
- Measure your space. A dent can slightly change the profile of a side panel. Confirm the unit still fits your cutout with the clearance you need.
- Ask about the model's age. Scratch and dent can be a current model or a discontinued line. Either is fine, but you should know which you are buying.
Scratch and Dent vs Open-Box vs Used
These three terms get confused. Here is the plain comparison.
| Factor | Scratch and Dent | Open-Box | Used |
|---|---|---|---|
| Function | New or like-new, tested | Tested, usually never installed | Previously owned, inspected |
| Appearance | Visible scratch or dent | Minor marks, if any | Signs of normal use |
| Price | Lowest of the three | Discounted from new | Discounted, varies by age |
| Warranty (ours) | 1-year | 1-year on open-box | 2-month on used |
| Best for | Built-in installs that hide the mark | Near-new condition for less | Lowest price on a working unit |
Shop in Calgary, Saskatoon or Regina
Our scratch-and-dent stock changes daily as marked units come in and go out. The best way to see what is available right now is to check your nearest store's scratch-and-dent collection, then come in or call. You can read our full warranty terms on our warranty page.
